详情介绍

产品名称：KUKA库卡机器人更换平衡缸KR360-2C下探式倒挂式平衡杠

产品型号：KR360-2C

产品品牌：库卡KUKA

产品类型：下探式倒挂式平衡缸

产品用途：KUKA KR360机器人

质保一年，可开专票

Product Name: KUKA Kuka Robot Replacement Balance Cylinder KR360-2C Downward Exploring Inverted Balance Bar
Product model: KR360-2C
Product brand: Kuka KUKA
Product type: downward probing inverted balance cylinder
Product Usage: KUKA KR360 Robot
One year warranty, with a special ticket available

KUKA机器人更换平衡缸

一、适用情况：

二、安全注意事项：

挂安全门锁，挂维修警示牌，面板下电。

准备事项：

工具：内六角，卡簧钳，套筒扳手，M12螺丝的拔销器，轴承。

三、操作步骤：

1，将机器人开到零位，先取出插销内的螺丝，在用卡簧钳取出卡簧，后用拔销器取出插销，然后在取出飞碟圆盘。
2，对内部进行清洁
3，先拆三角架这侧轴承，（注：三脚架下方有2颗M14的螺丝）。要取出侧面的轴承先要拆掉罩壳和一个固定螺丝，使用木棍支撑，慢慢撬动，待到合适位置，用吊绳捆绑，最后取下平衡缸，在地上平稳放好。
4，拆除三角架里的轴承和对面轴承，并清洗干净，有毛刺的地方用砂纸打磨光滑。然后更换新轴承和轴承卡簧。(注：安装轴承时请上高温润滑脂)

5，将平衡缸用安全带捆好抬到原来的位置，并装上三角盘里的轴承，注意要对准螺丝孔的位置，安装方法：先安装后面2个轴承并固定，在安装前面轴承和插销，(注：安装前面轴承时要用螺丝顶住平衡缸后面的弹簧板，将其往前顶，调整前方轴承方向和飞碟圆盘，到合适的位置装入插销)。

6，向该位置的圆盘打入4根螺丝，目的是使插销那里的轴承对准位置

7，对准平衡缸的位置后，重新装上插销，装上卡簧、罩壳后完成整个过程。

（注：完成后用油枪给轴承加高温润滑油.)

如果你有关于机器人任何配件的维修咨询，请即时与湖南驰开智能机器人有限公司联系吧。

KUKA Robot Replacing Balance Cylinder
1、 Applicable situation:
2、 Safety precautions:
Hang safety door locks, hang maintenance warning signs, and power down the panel.
Preparation:
Tools: hexagonal socket, circlip pliers, socket wrench, M12 screw extractor, bearing.
3、 Operating steps:
1. Drive the robot to the zero position, first remove the screw inside the pin, then use a snap ring pliers to remove the snap ring, then use a pin extractor to remove the pin, and then remove the flying disc.
2. Clean the interior
3. First remove the bearing on this side of the tripod (note: there are two M14 screws below the tripod). To remove the side bearing, first remove the cover and a fixed screw, use a wooden stick to support it, slowly pry it, wait until it reaches the appropriate position, bind it with a lifting rope, and finally remove the balance cylinder and place it smoothly on the ground.
4. Remove the bearings in the tripod and the opposite bearing, clean them thoroughly, and smooth any burrs with sandpaper. Then replace the bearings and bearing circlips with new ones. (Note: Please apply high-temperature lubricating grease when installing bearings)
5. Tie the balance cylinder with a safety belt and lift it to its original position. Install the bearings in the triangular disc, paying attention to aligning them with the screw holes. Installation method: first install the rear 2 bearings and fix them, and then install the front bearing and pin. (Note: When installing the front bearing, use screws to support the spring plate behind the balance cylinder, push it forward, adjust the direction of the front bearing and the flying disc, and install the pin in the appropriate position).
6. Drive 4 screws into the disc at this position to align the bearing at the pin with the position
7. After aligning the position of the balance cylinder, reinstall the latch, install the circlip, and complete the entire process.
(Note: After completion, use an oil gun to add high-temperature lubricating oil to the bearing.)

KUKA库卡机器人更换平衡缸KR360-2C下探式倒挂式平衡杠

湖南驰开智能机器人有限公司提供工业机器人系统化服务，致力于投身工业机器人自动化行业十多年，喷涂机器人、点焊机器人、码垛机器人，编程调试、维修保养、技术支持。诚信为本，严守标准！所售产品经过严格测试和认证。

我司有大量样机测试平台，可为客户提供检测。首先了解客户设备故障，为客户确认故障点，并提供解决方案及报价，客户可选择发至我司维修检测或者技术工程师出差服务，维修产品测试正常后发货。

我们将以的品质、的信誉、真诚积极的合作态度，与您建立一种互信、稳固、可靠、久远的合作关系。为企业提供机器人问题系统解决方案！

欢迎查看主页右上角咨询我们——湖南驰开智能机器人有限公司

KUKA库卡机器人更换平衡缸KR360-2C下探式倒挂式平衡杠

优势品牌：ABB；发那科FANUC；安川YASKAWA；KUKA库卡；川崎Kawasaki；西门子SIEMENS；横河Yokogawa；德国钴领guhring；FESTO费斯托；OMRON欧姆龙；Nabtesco纳博特斯克

KUKA KUKA KR360-2HC2 FLR2H360 Gear Five 500KG Driving Wheel
KUKA KUKA 1FK7105-5AY81-1YY3-Z S18 00131491
KUKA KUKA KRC2 MGV PH803-2830 00-110-699
KUKA KUKA KSP 600-3 * 20 00198266
KUKA KUKA 10DCCG5B 00-177-96
KUKA KUKA KCP KRC2 00-107-264
KUKA Kuka Robot KRC4 Teaching pendant 00168334
KUKA KUKA MG_ 03_ 40_ 60 servo motor 00201179
KUKA KUKA ATX KRC4 power module DC Input 27V/11A
KUKA KUKA servo motor TSM3102N8032E207
KUKA KUKA servo motor TSM3204N8332E207
KUKA KUKA 00275478 servo motor ME_ 06_ 60_ thirty
KUKA KUKA 00120420 servo motor 1FK7034 5A791 1ZZ9 7
KUKA KUKA 00115927 Servo Motor 1FK7032-5AK71-1ZZ9-Z
KUKA Kuka Mg_ 20_ 84_ 45 servo motor 00200589
KUKA Kuka Mg_ 35_ 84_ 25 Motor 00-200-588
KUKA KUKA KSD1-08 E93DA22214B531
KUKA KUKA C4 Balancing Rod M1160 B1C Balancing Cylinder
KUKA harmonic reducer 32-160
Kuka KUKA reducer 2011K26189
KUKA KUKA KR360-2C downward probing balance cylinder
KUKA KUKA R460 GA16 balance cylinder C4 balance bar 189401
KUKA KUKA 622V 500-3 Robot
KUKA KUKA 500-3 Robot